How this is written
Interior Building

Spray Foam Insulation Cost: Price Per Square Foot

Spray foam insulation cost breaks down by the board foot, open-cell versus closed-cell, and by project, the installed pricing our quantity manuals skip.

Short answer: As an illustrative planning range, open-cell spray foam commonly runs 1 to 1.50 dollars per board foot installed, with closed-cell running higher at 1.50 to 3 dollars, a board foot being one square foot of coverage at one inch of thickness. A rim joist job commonly runs 400 to 1,500 dollars, and a full 1,500 square foot attic filled to a typical depth often lands near 4,000 to 9,000 dollars, well above blown-in fill at the same R-value.

A stack of drywall panels leaning against open wall studs in an unfinished room, the stud bays empty, with a window letting in daylight
What's on this page
  1. How much does spray foam insulation cost
  2. The board foot: spray foam’s actual pricing unit
  3. Open-cell versus closed-cell: the real cost comparison
  4. Beyond R-value: what else closed-cell buys
  5. Pricing a whole attic
  6. Pricing a rim joist
  7. Pricing a wall
  8. DIY kits: what they can and cannot do
  9. Why spray foam costs more than batts or blown-in fill
  10. What drives spray foam insulation cost
  11. Spray foam versus rigid foam board
  12. Fire and vapor considerations
  13. New construction versus retrofit cost
  14. Health, safety, and reoccupying a sprayed space
  15. Spray foam and later home inspections
  16. Permits and inspection
  17. Regional cost swings
  18. Ways to keep spray foam insulation cost down
  19. Comparing spray foam bids line by line
  20. A worked example: a rim joist and a small wall section priced
  21. The bottom line

Short answer: As an illustrative planning range, open-cell spray foam commonly runs 1 to 1.50 dollars per board foot installed, with closed-cell running higher at 1.50 to 3 dollars, a board foot being one square foot of coverage at one inch of thickness. A rim joist job commonly runs 400 to 1,500 dollars, and a full 1,500 square foot attic filled to a typical depth often lands near 4,000 to 9,000 dollars, well above blown-in fill at the same R-value.

Spray foam insulation cost is the number our own insulation manual deliberately declines to price by the bag, because spray foam is not sold or installed the way batts and blown-in fill are. It is mixed on site from two chemical components, applied wet by a trained applicator with specialized equipment, and priced as an installed service rather than a retail product with a printed coverage chart. That different delivery model is exactly why spray foam needs its own cost brief rather than a line inside a quantity manual built around bags and packages.

This cost brief prices spray foam the way a spray foam contractor actually bids a job: per board foot, the industry’s standard coverage unit, broken out by open-cell versus closed-cell, then scaled to whole-project totals for the attics, walls, and rim joists where spray foam actually gets used. It is the cost companion to our insulation manual and our R-value manual, which price batts and blown-in fill and set the R-per-inch figures this brief carries forward unchanged. Run your own project through the estimator or the companion below as you read.

Key takeaways

  • Open-cell spray foam commonly runs an illustrative 1 to 1.50 dollars per board foot installed, closed-cell runs higher at 1.50 to 3 dollars, a real premium over batts or blown-in fill at the same R-value.
  • A board foot is one square foot of coverage at one inch of thickness, the industry's standard spray foam pricing unit, distinct from the lumber board foot despite sharing the name.
  • Closed-cell's higher R-per-inch, commonly cited near 6.2 against open-cell's roughly 3.6, means it needs less thickness to hit the same R-value target, narrowing the real cost gap at equal performance.
  • Rim joists, rooflines, and irregular gaps are where spray foam's air-sealing advantage earns its premium most clearly, which is why most whole-house jobs use it there and cheaper fill everywhere else.
  • Every dollar figure here is illustrative and local: thickness, cell type, access, and region move the real number more than any single rate, so get a written bid.

How much does spray foam insulation cost

The cleanest unit for pricing spray foam is dollars per board foot, one square foot of coverage at one inch of thickness, because that is how contractors quote the material and how a thickness decision translates directly into a price. As an illustrative planning range, open-cell spray foam commonly runs 1 to 1.50 dollars per board foot installed, while closed-cell runs noticeably higher, 1.50 to 3 dollars per board foot, reflecting its denser chemistry and higher material cost.

Turning that into a whole-project figure means multiplying the board foot rate by both the square footage of the surface and the thickness in inches, since a board foot already bundles both dimensions into one number. A 500 square foot wall sprayed at 2 inches of open-cell is 1,000 board feet, which at an illustrative 1.25 dollars a board foot lands near 1,250 dollars. The companion below runs this exact math on your own project as you go.

The board foot: spray foam’s actual pricing unit

A board foot in the spray foam trade means precisely what it sounds like on paper, one square foot of surface covered to one inch of thickness, and it is worth naming explicitly because the same term, board foot, is also a lumber volume measurement our own board foot manual covers for an entirely different product. The two share a name and a similar arithmetic structure, area times a thickness dimension, but they price two completely different materials, so do not confuse a lumber supplier’s board foot quote with a spray foam contractor’s.

Pricing by the board foot is what lets a spray foam quote scale cleanly with both your square footage and your target thickness in one combined number, rather than needing a separate rate for every possible depth the way a per-square-foot quote without a stated thickness would. Once you know your surface area and your target thickness, multiplying the two gives board feet directly, and multiplying that by the per-board-foot rate gives your installed cost estimate.

Open-cell versus closed-cell: the real cost comparison

Closed-cell spray foam costs roughly one and a half to two times what open-cell costs per board foot, but comparing the two purely on that per-board-foot number is misleading, because closed-cell’s R-value per inch is also far higher. As this site’s R-value manual already establishes, closed-cell commonly runs near R-6.2 per inch against open-cell’s roughly R-3.6, which means closed-cell needs meaningfully less thickness to reach the same target R-value.

Run the comparison at equal R-value rather than equal thickness and the real cost gap narrows substantially. To hit an illustrative R-20, open-cell needs about 5.5 inches, 5.5 board feet of coverage per square foot, while closed-cell needs only about 3.2 inches, 3.2 board feet per square foot. Multiplying each by its own per-board-foot rate brings the two products closer in total installed cost per square foot than their raw per-board-foot prices alone would suggest, even though closed-cell still typically comes out somewhat higher.

Illustrative R-value per inch, open-cell versus closed-cell spray foam

The figures this brief and our R-value manual both use; closed-cell's higher rating is why it needs less thickness to match a target.

Open-cell spray foam~3.6/inch
Closed-cell spray foam~6.2/inch

Closed-cell's nearly double R-per-inch rating is the reason a thinner closed-cell pass can match or beat a thicker open-cell one on total R-value, which matters directly when comparing board foot quotes between the two products.

Beyond R-value: what else closed-cell buys

R-value per inch is not the only difference between the two products, and the rest of the comparison often matters as much as the cost once you understand it. Closed-cell foam is dense enough to add real structural rigidity to the assembly it is sprayed into, genuinely stiffening a wall or roof deck in a way open-cell’s softer, more flexible cell structure does not. Closed-cell is also effectively its own vapor barrier once cured, which can be an advantage or a complication depending on the specific assembly and climate, since trapping moisture on the wrong side of a wall is a real risk if the rest of the assembly is not designed around it.

Open-cell is softer, more flexible, and allows some vapor to pass through it, which in many assemblies is actually the safer choice, letting any moisture that does get in dry out rather than becoming trapped. Open-cell is also notably better at sound dampening than closed-cell, a genuine secondary benefit for interior partition walls where noise control matters as much as thermal performance. Choosing between the two is a building-science decision as much as a cost one, and it is worth discussing your specific assembly and climate with a qualified installer rather than choosing purely on price.

A hand-drawn floor plan on graph paper with a metal ruler and a calculator resting beside it on a wooden table
Measuring the actual square footage of a wall or roof section before calling a spray foam contractor is the same first step this brief's companion runs, turning a floor plan into the board feet a quote will be based on.

Pricing a whole attic

An attic floor insulated to a high target R-value, an illustrative R-49 to R-60 in most climates, needs a genuinely deep fill, 14 to 17 inches at open-cell’s roughly 3.6 R per inch, which at spray foam’s per-board-foot price makes a full-depth open-cell attic fill one of the more expensive ways to hit that target compared with blown-in fiberglass or cellulose covering the same open floor, priced in full in our insulation manual.

Because of that cost gap, spray foam is far more commonly used in an attic for the roofline itself, when converting an attic to conditioned space, or for sealing irregular gaps, chimney chases, wiring penetrations, and the attic’s own rim joists, rather than filling the entire open floor edge to edge. A 1,500 square foot attic floor fully filled with open-cell at a typical 14 inch depth is 21,000 board feet, which at an illustrative 1.25 dollars a board foot reaches roughly 26,000 dollars, a figure that makes plain why most attics still use loose fill for the bulk of the job.

Pricing a rim joist

Sealing a home’s rim joists, the band of framing around the top of the foundation wall where the floor structure sits, is one of the most common and most cost-effective single applications of spray foam in an existing home, because the irregular gaps around floor joists, sill plates, and sistered framing members are genuinely difficult for a cut batt to seal completely. As an illustrative figure, a typical home’s full rim joist perimeter commonly runs 400 to 1,500 dollars professionally sprayed at about 2 inches of closed-cell, depending on the home’s total perimeter length and foundation height.

This job is frequently cited as the single best dollar-for-dollar air sealing investment available in an older home’s building envelope, because the labor and setup for a project this size is modest relative to a whole-house job, while the air leakage it closes is often disproportionately large. Our crawl space encapsulation cost brief covers this same rim joist sealing step as part of a full crawl space project, for anyone pairing the two.

Pricing a wall

Spray-foaming a stud wall’s cavities, most commonly in new construction or a gut renovation where the wall is open and accessible, prices by the same board foot math as any other surface. A standard 2 by 6 wall, 5.5 inches deep, filled completely with open-cell reaches about 19.8 R, 5.5 board feet per square foot of wall, while the same cavity filled completely with closed-cell reaches about 34 R at the same 5.5 board feet, a dramatic R-value difference for the identical thickness and material volume.

In practice, many walls use a hybrid approach called flash-and-batt, a thin 1 to 2 inch pass of closed-cell sprayed against the sheathing to seal air leaks and add a vapor-retarding layer, followed by a standard batt filling the remaining cavity depth, which captures much of spray foam’s air-sealing benefit at a fraction of the cost of filling the entire cavity with foam alone. As an illustrative figure, a full wall spray foam job for an average home’s exterior walls, open-cell filled to the full cavity depth, commonly runs 3,000 to 7,000 dollars for a modest single-story home, well above a flash-and-batt approach covering the same walls.

A pencil, a ruler, and a calculator resting on a lined ledger sheet under warm desk lighting
Working through board feet and a per-unit rate on paper before a contractor's own quote arrives is the same exercise this brief's method walks through, just with a pencil instead of the companion below.

DIY kits: what they can and cannot do

Small two-part DIY spray foam kits are a genuine, useful product category, commonly running an illustrative 300 to 600 dollars per kit and covering a few hundred board feet at a thin sealing thickness, well suited to sealing modest gaps around a window, a pipe or wire penetration, or a short section of rim joist. For that scope, a kit is a realistic and cost-effective do-it-yourself option that avoids hiring a contractor for a small job.

What a DIY kit is not realistically built for is filling an entire wall cavity, an attic floor, or a whole rim joist perimeter at professional scale. Professional equipment mixes the two chemical components at a controlled ratio, temperature, and pressure, and applies them through equipment designed to maintain that control across a large continuous area, a level of process control a small consumer kit’s simpler delivery system cannot reliably match once the area grows beyond a modest sealing task. Treat a DIY kit as a sealing tool for specific gaps, not a substitute for a professional whole-cavity fill.

Why spray foam costs more than batts or blown-in fill

At equal R-value, spray foam commonly costs two to four times what batts or blown-in loose fill cost installed, and that premium traces to a few real factors rather than simple markup. The material itself is a specialized two-component chemical product, meaningfully more expensive per unit of coverage than fiberglass or cellulose. The equipment, a heated hose system and a trained two-person crew, represents a real capital and training investment that a batts installer or a blown-in fill crew does not need. The application itself also moves more slowly and carefully than unrolling a batt or blowing loose fill through a hose.

What that premium buys, beyond raw R-value, is the air sealing performance covered throughout this brief, which a bag of fiberglass or cellulose simply does not provide no matter how carefully it is installed. Our insulation manual prices batts and blown-in fill in full, and comparing its figures against this brief’s board foot rates at the same target R-value is the clearest way to see exactly what that premium is paying for.

What drives spray foam insulation cost

Beyond the cell type and the thickness, a handful of job-specific factors move a spray foam quote within its own range. Access is a major one: a wide-open, easily reached attic or wall cavity is far faster to spray evenly than a cramped crawl space or a tight, obstructed wall cavity full of wiring and plumbing, and labor time, not material, is frequently the largest share of an installed spray foam price. Temperature and humidity at the time of application also matter, since the chemical reaction that cures spray foam is sensitive to both, and a job in a very cold or very humid space sometimes needs extra setup, like temporary heating, to apply correctly.

The total square footage and whether the job is a small, standalone task like a rim joist versus a full-house application also shifts the effective rate, since a small job absorbs the crew’s setup and equipment mobilization cost across fewer board feet, similar to how a short-load fee inflates a small concrete order’s effective per-yard price. Existing obstructions, old insulation that has to be removed first, or framing that needs minor repair before spraying, each add real time beyond the bare material and thickness math.

The crew’s travel distance from their base and whether your job can be scheduled alongside another nearby job on the same day also factors into smaller jobs more than larger ones, since a standalone rim joist job in a remote location absorbs a full day’s travel cost across a comparatively small scope, while a crew already working in your neighborhood on a larger project can sometimes fit a small add-on job in for less.

Spray foam versus rigid foam board

Rigid foam board is the other common high-R-per-inch insulation product, our R-value manual citing it at an illustrative R-5 to R-6 per inch, close to closed-cell spray foam’s own rating, which raises the natural question of why anyone chooses the more expensive sprayed product over a cut-to-fit rigid panel. The answer is almost entirely about irregular surfaces and air sealing. Rigid board is cut to a shape and fitted into place, which works well on a flat, regular surface but leaves gaps at every seam, corner, and penetration unless each one is separately taped or sealed by hand.

Spray foam expands to fill whatever irregular cavity it is sprayed into, sealing around wiring, plumbing, and framing irregularities in one continuous pass without the seam-by-seam sealing labor rigid board demands to achieve a comparable air seal. For a flat, simple surface like an exterior wall sheathing layer with few penetrations, rigid board commonly costs less installed for a similar R-value and air sealing result once properly taped. For an irregular surface, a rim joist, a complex roofline, or a cavity full of mechanical penetrations, spray foam’s one-pass sealing typically wins on total installed cost once you count the labor a rigid board installation would need to match the same air sealing result by hand.

Fire and vapor considerations

Spray foam, like most insulation products, commonly requires a fire-rated covering, typically drywall or a specific intumescent coating, in any living space where it would otherwise be left exposed, a code requirement rather than a cost preference, and our drywall installation cost brief prices that covering layer separately for anyone budgeting the full assembly. An attic or crawl space application sometimes has different exposure rules than a finished living space, so confirm your local code’s specific requirement for your application rather than assuming the same covering rule applies everywhere.

Vapor behavior is the other consideration worth understanding before choosing a cell type. Closed-cell’s near-total vapor resistance can be exactly right in some assemblies and genuinely risky in others, trapping moisture on the wrong side of a wall if the rest of the assembly was not designed with a vapor-closed layer in mind. This is a building-science question specific to your climate and wall assembly, not a universal rule, and it is worth a direct conversation with your installer rather than a decision made on R-value or cost alone.

New construction versus retrofit cost

Spraying foam into an open, unfinished wall or roof cavity during new construction is meaningfully faster and therefore somewhat cheaper per board foot than retrofitting the same R-value into an already finished home, because a retrofit crew often has to remove and later replace drywall, work around existing wiring and plumbing that is already in place, and protect finished flooring and fixtures from overspray. New construction access alone can shift an otherwise identical job’s effective rate down by a meaningful margin simply because the labor moves faster against an open stud bay with nothing in the way.

A retrofit is not always a straight wall-cavity fill for this reason. Many retrofit projects target the rim joist and other accessible gaps specifically because those areas do not require opening finished walls, which is part of why the rim joist job priced earlier in this brief is such a common standalone retrofit scope. A whole-house retrofit that does require opening walls should be priced with that demolition and patch-back labor as its own explicit line, not folded quietly into the spray foam rate alone.

Health, safety, and reoccupying a sprayed space

Spray foam off-gasses as it cures, and manufacturers specify a re-entry time, commonly in the range of 24 hours for occupants without respiratory protection, though the exact figure varies by product and should come from the manufacturer’s data sheet rather than a general rule. Anyone with asthma, chemical sensitivity, or other respiratory conditions should discuss the specific timeline and any extended precautions with the installer before the job, since individual sensitivity can call for more caution than the standard re-entry window.

A professional crew works in respirators and protective clothing during application precisely because the chemical components are hazardous in their uncured, airborne state, and that same caution is exactly why a DIY kit user should take ventilation and protective equipment seriously even on a small sealing job, not just on a whole-room application. Pets, in particular, should be kept out of a sprayed area for the full manufacturer-specified re-entry window, since they cannot be asked whether an odor is bothering them the way a person can.

Spray foam and later home inspections

A detail worth knowing before you spray foam a roofline or an attic: a fully sprayed, unvented roof assembly looks different to a home inspector or a future insulation contractor than a traditional vented attic with visible batts or loose fill on the floor, and it is worth keeping documentation of what was installed, the product, the thickness, and the date, for your own records and for a future sale. Some inspectors specifically note spray foam in a roof assembly and ask for documentation confirming it was installed correctly with adequate ventilation accounted for, since an improperly designed unvented assembly can trap moisture in ways that are expensive to diagnose after the fact.

This is not a reason to avoid spray foam, since a correctly designed assembly performs well and is increasingly common, but it is a reason to keep the installer’s paperwork, the specific product data sheet, and ideally a few photos of the open cavity before it was covered, filed away with your other home records. That documentation is cheap to keep at the time of installation and can save real back-and-forth if a future buyer’s inspector or a future contractor has questions about an assembly they cannot see once it is finished.

Permits and inspection

Whether spray foam insulation requires a permit depends on your jurisdiction and the scope of the work, and it often ties to whatever larger project the insulation is part of rather than being a standalone trigger on its own. A rim joist sealing job alone, with no other construction involved, is frequently exempt from a permit requirement in many places, while spray foam installed as part of a larger renovation, an addition, or new construction is typically covered under that project’s existing permit rather than needing its own.

Some jurisdictions require an inspection of open wall or roof cavities before they are covered with foam, similar to an insulation inspection for batts or blown-in fill, specifically to confirm the correct product, thickness, and any required fire-rated covering plan before the space is sealed up and no longer visible. Confirm your local requirement with your building department before work begins, particularly on any job that also involves opening finished walls, since skipping a required inspection can complicate matters later if you ever sell the home or file an insurance claim involving that area.

Regional cost swings

Every rate in this brief is a national illustrative figure, and the real number in your market moves with local labor costs and how many trained spray foam applicators compete for work in your area. Regions with a higher cost of living and fewer specialized crews commonly see rates toward the top of this brief’s ranges, while areas with more competition among installers and a lower overall labor cost commonly see quotes closer to the bottom.

Climate also plays a real role beyond labor pricing, since colder climates commonly specify thicker, higher R-value targets by code or by common practice, which raises the board foot count even before any regional rate difference enters the picture. A northern attic rim joist and a southern one sealed to the same 2 inch thickness might cost similarly per board foot, but a northern wall cavity filled to a higher target R-value for its climate zone will cost more in total simply because it needs more material.

Ways to keep spray foam insulation cost down

A few real levers exist even for a specialized, labor-heavy trade like this one. The clearest is scope discipline: targeting spray foam specifically at the rim joist, the roofline, and irregular gaps where it earns its premium, while using cheaper batts or blown-in fill for simple, open cavities where foam’s air-sealing advantage adds little beyond what a careful batt installation already achieves. This single choice, covered throughout this brief, is the biggest cost lever available on most whole-house projects.

Clearing access to the work area yourself, moving stored items out of an attic or basement before the crew arrives, removes labor time that would otherwise be billed. Bundling several small sealing tasks, the rim joist, a few wall penetrations, and an attic hatch, into one visit spreads the crew’s equipment mobilization cost across more total board feet, similar to how batching concrete pours avoids a short-load fee. What should never be cut is the thickness needed to hit your climate’s target R-value or the fire-rated covering code requires, since both are safety and performance decisions, not places to trim for savings.

Comparing spray foam bids line by line

Spray foam bids vary more than almost any other home-improvement trade’s quotes, and a lump-sum total without specifics is the hardest kind to judge fairly. Ask every bidder to state the specific product and cell type by name, the target thickness in inches for every area being sprayed, and whether any fire-rated covering or cleanup is included in the quoted price. A bid that reads only as a single dollar figure for the whole job, with no thickness or product stated, is not a comparable bid against one that itemizes both.

Two quotes for the same labeled job can differ substantially in real installed R-value if one assumes a thinner pass or a lower-performing formulation than the other, so a lower number is not automatically the better value once the actual thickness and product are confirmed. Request the manufacturer’s data sheet for the specific foam product being proposed if a quote seems unusually far from others for the same stated scope, since the gap is more often a thinner spec than a genuine discount.

A worked example: a rim joist and a small wall section priced

Take a common combined job end to end: sealing a typical home’s full rim joist perimeter at 2 inches of closed-cell, plus spray-foaming a small 200 square foot basement wall section at 3 inches of open-cell as part of the same visit. The rim joist, say 160 linear feet of perimeter at an average 10 inches of exposed band height, is roughly 133 square feet of surface, 266 board feet at 2 inches, which at an illustrative 2 dollars a board foot for closed-cell is about 532 dollars.

The wall section is 200 square feet at 3 inches, 600 board feet, which at an illustrative 1.25 dollars a board foot for open-cell is about 750 dollars. Combined, the two scopes total roughly 1,280 dollars before any mobilization minimum, with the rim joist alone falling comfortably inside this brief’s illustrative 400 to 1,500 dollar range for that scope. The chart below places a few common project scopes side by side on total installed cost for context.

Illustrative total installed cost, by common spray foam project

Representative scopes at typical thickness for each use; your own square footage and thickness will move every figure.

DIY sealing kit~$450
Rim joist, full perimeter~$900
Small wall section, 200 sq ft~$750
Whole-house wall cavities~$5,000

A rim joist and a small sealing scope sit far below a whole-house wall application, which is exactly why most real jobs use spray foam at specific trouble spots rather than across an entire home's insulation.

Where a professionally installed spray foam job's cost goes

Illustrative split for a standard rim joist or small wall job.

Labor ~40% Material ~40% Equipment & setup ~20%
Applicator labor and finishing, ~40% The two-component chemical material itself, ~40% Equipment mobilization, setup, and temperature control, ~20%

Material carries a far larger share of a spray foam job than it does for batts or blown-in fill, which is the direct result of the specialized chemistry the product itself requires.

Run your own surface area, target thickness, and cell type through the companion below to see how your specific project compares.

The bottom line

Spray foam insulation cost comes down to a short list in a fixed order: the surface area, the target thickness in inches, and whether you choose open-cell or closed-cell. As an illustrative planning range, open-cell runs 1 to 1.50 dollars per board foot installed and closed-cell runs 1.50 to 3 dollars, and you turn either into a project total by multiplying the rate by both your square footage and your thickness, the board foot math this entire brief is built around.

Remember that spray foam earns its real premium at the places batts and loose fill struggle, rim joists, rooflines, and irregular penetrations, which is why most whole-house jobs use it selectively rather than throughout. Measure your own project with our square-footage manual or the estimator, price it in the companion below, read our insulation manual for the cheaper fill options spray foam is often paired with, then collect written bids that state the product, cell type, and thickness explicitly, the same three details that separated a fair comparison from a guess throughout this brief. Priced that way, spray foam stops being a mystery line on a renovation estimate and becomes a number you can judge.


Treat this as workbench education, not a price quote or an engineering specification. Every dollar figure here, per board foot, by cell type, and by project, is an illustrative planning range, and your specific product, thickness, access, climate, and region will each move the real numbers, often significantly. Vapor behavior, required thickness for your climate zone, and any fire-rated covering requirement are building-science and code decisions that should be confirmed with a qualified insulation contractor before material is sprayed, not assumed from any figure in this brief. Build your actual budget on a live, written quote that states the specific product, cell type, and thickness proposed for your exact project, not on any illustrative range alone.

Frequently asked questions

How much does spray foam insulation cost?

As an illustrative planning range, professionally installed open-cell spray foam commonly runs 1 to 1.50 dollars per board foot, a board foot being one square foot of coverage at one inch of thickness, while closed-cell runs noticeably higher, an illustrative 1.50 to 3 dollars per board foot. For a whole project rather than a unit price, a 1,500 square foot attic floor filled to a typical depth with open-cell often lands somewhere near 4,000 to 9,000 dollars, and a smaller job like sealing a rim joist commonly runs a few hundred to about 1,500 dollars as its own standalone scope. Get a written local quote, since the specific thickness, the cell type, and how accessible the space is move the real figure more than any single table.

What is the difference between open-cell and closed-cell spray foam cost?

Closed-cell spray foam costs roughly 1.5 to 2 times what open-cell costs per board foot, an illustrative 1.50 to 3 dollars against open-cell's 1 to 1.50, because closed-cell is a denser, more expensive chemistry that also delivers a far higher R-value per inch, commonly cited around 6.2 compared to open-cell's roughly 3.6. That means closed-cell needs less thickness to hit the same R-value target, which narrows the real installed cost gap between the two once you compare them at equal R-value rather than equal thickness. Closed-cell also adds structural rigidity and acts as its own vapor barrier, two properties open-cell does not share, which is often what actually decides between them beyond price alone.

How much does it cost to spray foam an attic?

An attic floor is commonly insulated to a high R-value, an illustrative R-49 to R-60 in most climates, which at open-cell's roughly 3.6 R per inch means 14 to 17 inches of material, a genuinely deep and costly fill at spray foam's per-board-foot price compared to blown-in loose fill at the same R-value. Because of that cost gap, many attics are insulated with blown-in fiberglass or cellulose instead and spray foam is reserved for the attic's rim joists, roofline, or any irregular gaps loose fill cannot seal well, rather than filling the entire open attic floor with foam from edge to edge.

How much does spray foam cost for a rim joist?

Sealing a home's rim joists, the band around the top of the foundation wall where the floor framing sits, with spray foam is one of the most common and most cost-effective single uses of the material, because it seals irregular gaps around framing members far more completely than a cut batt ever can. As an illustrative figure, a typical home's full rim joist perimeter commonly runs 400 to 1,500 dollars professionally sprayed at 2 inches of closed-cell, depending on the home's perimeter length and foundation height. This is frequently the single best dollar-for-dollar air sealing investment in an older home's building envelope.

Can I spray foam my own walls with a DIY kit?

Small two-part DIY spray foam kits exist and are genuinely useful for sealing modest gaps, around a window, a pipe penetration, or a small section of rim joist, commonly running an illustrative 300 to 600 dollars per kit and covering a few hundred board feet at a thin sealing thickness. What DIY kits are not realistically built for is filling an entire wall cavity or attic at scale, since professional equipment mixes and applies the two chemical components at a controlled ratio, temperature, and pressure that a small kit's simpler delivery system cannot reliably match across a large area. Treat DIY kits as a sealing tool, not a whole-house insulation method.

Is spray foam insulation worth the extra cost?

Spray foam costs meaningfully more than batts or blown-in fill at the same R-value, and whether that premium is worth it depends on what you actually need from the insulation. Where air sealing irregular gaps matters as much as the R-value itself, a rim joist, a complex roofline, or a wall with many penetrations, spray foam's ability to seal and insulate in one step is hard for any other product to match. For a simple, open attic floor or a standard wall cavity with few penetrations, blown-in fill or batts commonly deliver the same R-value for meaningfully less money, which is exactly why most whole-house jobs mix spray foam at the trouble spots with cheaper fill everywhere else.

How does spray foam insulation cost compare to batts or blown-in fill?

At equal R-value, spray foam commonly costs two to four times what batts or blown-in loose fill cost installed, a real premium driven by the specialized equipment, trained applicator labor, and the chemical material itself. Our insulation manual prices batts and blown-in fill by the bag and the package, and the gap between that figure and spray foam's per-board-foot price is almost entirely the air sealing and gap-filling performance spray foam adds on top of raw R-value, a benefit a bag of fiberglass simply does not provide regardless of how it is installed.

Why do spray foam quotes vary so much between contractors?

Spray foam pricing swings widely because the material, labor, and markup structure differs more between spray foam contractors than it does for most other home-improvement trades, partly because the equipment and training investment is substantial and partly because job conditions, access, temperature control, and existing gaps vary enormously from one house to the next. A quote that seems unusually low relative to others is worth a direct question about the specific product, thickness, and cell type being applied, since a thinner pass of a cheaper formulation can look like a bargain on paper while delivering meaningfully less R-value and air sealing than a higher quote for the same labeled job.

Editorial team · Estimating-tool explainers

GaugeYard tools and guides are written by our editorial team, and every calculator documents the formula behind it so the output can be checked by hand. Figures are illustrative and labelled, and code requirements point to the authority that publishes them.

By email

Get a material cost breakdown by email

Tell us what you need hauled and we'll email you a breakdown of what that material and quantity typically costs delivered, and how haul distance moves the price. We are not a supplier or a hauler, we do not deliver, and we cannot quote your site.

We store your details to reply to you. See our privacy policy.